The factory exhaust manifolds on your 4th Gen Camaro Z28 or Firebird are one of the first restrictions holding back your Gen 2 LT1. Speed Engineering's 1-3/4" longtube headers are a direct-fit, dyno-proven upgrade that frees up exhaust flow, improves throttle response, and delivers over 20 rear-wheel horsepower over stock. Built from 304 natural stainless steel with mandrel-bent primary tubes, CNC-machined flanges, and full TIG-welded construction.
⚠️ Important Note: Some earlier LT heads have a wider bolt spread. These headers measure 17-3/8" from front center bolt hole to rear center bolt hole. Verify your cylinder head bolt spacing before ordering.
Features:
- Full 1-3/4" Primary Tubes — Sized for maximum flow on Gen 2 LT1 5.7L applications
- 3" Collector — Optimized for strong low-to-mid RPM torque
- Mandrel Bent Tubing — Consistent tube diameter through every bend; no crimping, no restriction
- CNC Machined Flanges — Precision fit at the head and collector for a leak-free seal
- 304 Natural Stainless Steel Construction — Corrosion resistant, heat tolerant, and built to last
- Longtube Header Design — Maximum scavenging efficiency vs. shorty or mid-length headers
- Dyno Proven — 20+ RWHP gain on Gen 2 LT1 applications
- Compatible with Gen 2 LT1 5.7L Engines
Vehicle Applications:
Chevrolet Camaro Z28 — Gen 2 LT1 (RWD)
- 1993 Chevrolet Camaro Z28 (RWD) — 5.7L LT1
- 1994 Chevrolet Camaro Z28 (RWD) — 5.7L LT1
- 1995 Chevrolet Camaro Z28 (RWD) — 5.7L LT1
- 1996 Chevrolet Camaro Z28 (RWD) — 5.7L LT1
- 1997 Chevrolet Camaro Z28 (RWD) — 5.7L LT1
Chevrolet Camaro SS — Gen 2 LT1 (RWD)
- 1996 Chevrolet Camaro SS (RWD) — 5.7L LT1
- 1997 Chevrolet Camaro SS (RWD) — 5.7L LT1
Pontiac Firebird — Gen 2 LT1 (RWD)
- 1993 Pontiac Firebird (RWD) — 5.7L LT1
- 1994 Pontiac Firebird (RWD) — 5.7L LT1
- 1995 Pontiac Firebird (RWD) — 5.7L LT1
- 1996 Pontiac Firebird (RWD) — 5.7L LT1
- 1997 Pontiac Firebird (RWD) — 5.7L LT1
Pontiac Firebird Trans Am — Gen 2 LT1 (RWD)
- 1993 Pontiac Firebird Trans Am (RWD) — 5.7L LT1
- 1994 Pontiac Firebird Trans Am (RWD) — 5.7L LT1
- 1995 Pontiac Firebird Trans Am (RWD) — 5.7L LT1
- 1996 Pontiac Firebird Trans Am (RWD) — 5.7L LT1
- 1997 Pontiac Firebird Trans Am (RWD) — 5.7L LT1
FAQ
Will these headers fit all LT1 head configurations?
Some earlier Gen 2 LT heads have a wider bolt spread than standard. These headers measure 17-3/8" from front center bolt hole to rear center bolt hole. Verify your cylinder head bolt spacing before ordering to ensure proper fitment.
How much horsepower do these headers add?
Speed Engineering's 1-3/4" longtube headers are dyno proven to add over 20 rear-wheel horsepower on 1993–1997 Camaro and Firebird Gen 2 LT1 applications compared to stock exhaust manifolds.
Do these headers work on a Gen 5 LT1 (C7 Corvette, 5th Gen Camaro)?
No. These headers are designed specifically for the Gen 2 LT1 5.7L engine found in 1993–1997 Camaro Z28/SS and Firebird/Trans Am. They are not compatible with the Gen 5 LT1 engine found in the C7 Corvette or 6th Gen Camaro.
What material are these headers made from?
304 natural stainless steel with full TIG-welded construction and CNC-machined flanges.
Are these headers street legal?
No. These are race-only headers intended for closed-course competition use only. Installation on a street-driven vehicle may violate the Clean Air Act (42 U.S.C. 7522(a)(3)).
⚠️ Race Use Only: This product is manufactured and sold for installation on vehicles used solely for competition. Once installed, the vehicle may not be used, registered, or licensed for use on a public road or highway. Installation on a street-driven vehicle may violate the Clean Air Act 203(a)(3), 42 U.S.C. 7522(a)(3).