Terminator X Max is a self-learning Holley EFI engine management kit for domestic V8 engines, such as conventional pushrod Chevrolet and Chrysler engines. It replaces a factory or junkyard controller with real-time fuel learn, high-impedance injector drivers and Holley EFI tuning software. This version is configured for an EV1 injector harness, drive-by-wire throttle body control and GM 4L60E/4L80E transmission control. A 3.5 in. touchscreen handheld with a calibration wizard is included for setup, tuning and gauge display.
Key Features:
- Built for domestic V8 engines, such as conventional pushrod Chevrolet and Chrysler engines
- Real-time fuel map learning builds and refines the base fuel table
- High-impedance injector drivers run most stock injectors and Holley EFI injectors; low-impedance injectors are not supported
- Bosch LSU 4.9 wideband oxygen sensor control for accurate AFR readings and closed-loop tuning
- Built-in 1-bar MAP sensor suited to naturally aspirated or nitrous combinations
- For boosted use, the internal MAP sensor can be disabled and an external MAP sensor connected to the pre-terminated harness connector
- 4 programmable inputs (12V, ground, 5V, frequency) and 4 outputs (ground, PWM) for sensors, fans, boost and nitrous control, IAC kits and more
- Boost control by time, gear, RPM or speed, with boost safeties
- Single-channel wet or dry nitrous control, progressive or non-progressive, with rich/lean safeties and closed-loop AFR target
- Advanced 1D and 2D custom tables, including per-gear tables, for uses such as a flex fuel offset or a fuel or oil pressure safety
- On-board diagnostic LEDs for ECU power, engine run, wideband status, TPS calibration, crank signal and cam signal
- 3.5 in. touchscreen handheld with calibration wizard, internal data logging and customizable gauge display
- Plug-and-play ignition capability with Holley Dual Sync and HyperSpark distributors (HyperSpark requires adapter 558-323)
- Compact ECU can be mounted almost anywhere, with the diagnostic LEDs facing up
- Plug-and-play with Holley EFI gauges, shift lights, modules and digital/pro dashes (P/N 553-106, 553-111, 553-112)
- Free Holley EFI tuning software provides full laptop access for advanced users
Specifications:
- Engine: Universal domestic V8 (MPFI)
- Injector Connector: Jetronic/Minitimer (Bosch EV1)
- Throttle Control: Drive-by-wire (DBW)
- Transmission Control: GM 4L60E/4L80E
- MAP Sensor: 1-bar, internal
- Handheld Included: Yes, 3.5 in. touchscreen
- Part Number: 550-959
Not recommended for 4x4 applications with electronic transfer cases. Not compatible with 4L6X transmissions from model year 1995 or earlier because converter lockup and downshift strategy changed year to year. Not recommended for marine use; it can be used off-road when mounted in a safe, dry location protected from heat with proper wiring management.
FAQ
What engines does the 550-959 fit?
It is built for domestic V8 engines, such as conventional pushrod Chevrolet and Chrysler engines.
Is a handheld display included?
Yes. A 3.5 in. touchscreen handheld with a calibration wizard is included for setup, tuning and gauge display.
Does it control the throttle body and transmission?
Yes. It provides drive-by-wire throttle body control and GM 4L60E/4L80E transmission control.
What fuel injector connector does the kit use?
The injector harness uses the Jetronic/Minitimer (Bosch EV1) connector.
Can this be used on a 4x4 vehicle?
It is not recommended for 4x4 applications with electronic transfer cases.

