Looking for a complete axle-back exhaust system for your 4th Gen Camaro or Firebird that works with either your factory exhaust setup or the Speed Engineering off-road Y-pipe? This single 3" inlet exhaust system splits into a dual 2.5" exit configuration with an insulated bullet style blow-through muffler for a deep, aggressive tone. Built from 3" mandrel bent 304 natural stainless steel with 2.5" and 3" stainless band clamps included, finished with dual 4" exhaust tips.
⚠️ Important Notes:
- Designed to work with the factory exhaust system and the Speed Engineering off-road Y-pipe kit
- Lowered vehicles may require modification for proper ground clearance
Features:
- Mandrel Bent 3" Tubing — Consistent diameter throughout for maximum exhaust flow
- Single 3" to Dual 2.5" Exiting System — Splits into a dual exhaust configuration at the rear
- Insulated Bullet Style Blow-Through Muffler — Deep, aggressive exhaust tone with straight-through flow
- 2.5" & 3" Stainless Band Clamps Included
- Dual 4" Exhaust Tips
- 304 Natural Stainless Steel Construction — Corrosion resistant, heat tolerant, and built to last
- Compatible with 5.7L LS1/LS6 Engines
- Dyno Proven
Vehicle Applications:
Chevrolet Camaro & Pontiac Firebird — F-Body LS1 5.7L
- 1998 Chevrolet Camaro (RWD) — 5.7L LS1
- 1999 Chevrolet Camaro (RWD) — 5.7L LS1
- 2000 Chevrolet Camaro (RWD) — 5.7L LS1
- 2001 Chevrolet Camaro (RWD) — 5.7L LS1
- 2002 Chevrolet Camaro (RWD) — 5.7L LS1
- 1998 Pontiac Firebird (RWD) — 5.7L LS1
- 1999 Pontiac Firebird (RWD) — 5.7L LS1
- 2000 Pontiac Firebird (RWD) — 5.7L LS1
- 2001 Pontiac Firebird (RWD) — 5.7L LS1
- 2002 Pontiac Firebird (RWD) — 5.7L LS1
FAQ
Will this exhaust work with my factory exhaust manifolds?
Yes. This system is designed to work with the factory exhaust system, as well as the Speed Engineering off-road Y-pipe kit if you've upgraded your front-end exhaust.
Will this fit a lowered Camaro or Firebird?
Lowered vehicles may require modification for proper ground clearance.
What exit configuration does this system use?
This system uses a single 3" inlet that splits into a dual 2.5" exit configuration with dual 4" exhaust tips.
What muffler does this system use?
An insulated bullet style blow-through muffler for a deep, aggressive exhaust tone with straight-through flow design.
What material is this system made from?
304 natural stainless steel with mandrel-bent tubing and TIG-welded construction. 2.5" and 3" stainless band clamps are included.
Is this system street legal?
No. This is a race-only product intended for closed-course competition use only. Installation on a street-driven vehicle may violate the Clean Air Act (42 U.S.C. 7522(a)(3)).
⚠️ Race Use Only: This product is manufactured and sold for installation on vehicles used solely for competition. Once installed, the vehicle may not be used, registered, or licensed for use on a public road or highway. Installation on a street-driven vehicle may violate the Clean Air Act 203(a)(3), 42 U.S.C. 7522(a)(3).
Packing wasn't sufficient. The inlet pipe on the muffler got deformed during the shipping. It actually went through the side of the box.
Very nice system fits well.
Fast shipping,.great email communications. Cat back arrived quicker than expected. Installing this week but quality of chrome tips and welds look great. Will be buying from Berry again
Best exhaust for the money. Very easy to install. Fit and finish is very nice. Sounds great not too loud but loud enough to sound mean but with out causing drone inside the car.
